[NOTE]
This is a bit of a rant, but it does have useful information in it on making a bump map procedural texture (which I render in Yafray.) I don’t intend it to be abusive in any way, this is just the way I am after doing something for some 8 hours for what should have been a simple task. And I’m just venting some of my anger, it is not intended to be aimed at anyone or any group in particular, directly or indirectly. It’s just me in a frustrated state.
[/NOTE]
After countless hours of work, I have finally produced a simple procedural texture bump map. It involved pressing lots and lots of buttons and moving sliders and jiggling numbers between my erratic dances to the gods of computer programming, cgi and senility. I’m significantly more pleased with the latter, if it wasn’t for him sending me this beautiful oracle rock, I would have cracked hours before. I will write a simple tutorial of what buttons to press and what sliders to move to get results that are almost, but not quite, entirely like a beaten steel texture. Though you must excuse me as I consult with my rock for the many answers I need.
Ah, very wise O’ Oracle Rock. Yes. And if all you do the same bizarre and meaningless dance I did, you too may be granted a pet rock to keep your fine grip on senility while you Blender your homework presented here.
I don’t have any place to upload images too, so you’ll have to take this all as words and keep dancing to the senility dude that he too will send a rock to guide you.
Make a simple texture for a simple object. You could make something fancy, but I wouldn’t recommend it unless it makes you happy. Call the texture “oraclerocksacne”. Select “Cloud” as texture type. Switch to the Colors tab and make a colorband that has gray for the majority of its surface, but with some narrow brighter colors in between.
Blender makes the bump map from the relative brightness of the colorband. Brighter can mean it is a low point or high point, while darker can mean it is a high point or low point. You can change that but I don’t know how, so my bump map is currently inverted, but I haven’t despaired yet.
You want the bright bars surround by the gray bars. This will keep the bright spots in the preview small. But before you knock yourself out, head over to the Clouds Panel on the far right. Ensure that you have “default” and “soft noise” selected. Set noisedepth to 1 and noisesize to 0.1. Set nabla to .025 and the Noise Basis to Blender Original. You will have to tweak some of those values (to be specified shortly) and the position of the colored bars in the Colors tab until you have lots of small bright spots scattered across the preview.
The values you’ll want to edit are NoiseSize and the position and number of the color bars. Leave everything else, or else the cgi god will rain down his fury upon you.
Toggle to the other part of the Material section of the Shading Menu (F5, let’s face it, if you didn’t know that, you shouldn’t be reading this tutorial yet.) You can safely ignore all the settings except what is in the Texture, Map Input and Map To tabs. In the Texture tab, make sure your texture is selected, and only your texture. If it’s not, fix it. In Map Input, select ORCO and CUBE. You’ll probably have to tweak the sizeX,Y,Z values later. But for now, leave them at their default settings.
Next go to Map To Tab. Select the NOR tab, make sure all the other tabs in that block are unselected. In the drop down menu select “ADD” (I don’t know if it does anything with this type of texture, but I’m afraid to start tweaking again.) In the column on the right, with the Col, Nor, Var, Disp and Warp settings from top to bottom, start editing them as follows.
Col = 0.0
Nor = 16.93
Var = 0.0
Disp = 0.0
Warp = OFF
Fac = 0.0
Go to the column on the left, make sure Stencil, Neg and No RGB are NOT selected. Set Red and Blue to 1.0, and Green to 0.0. Set DVar to 1.0.
Do a test render. Depending how things go, you may have a beautiful steel bump map that is just screaming to be sent to the finished projects section of this forum. Or, if you’re like me, you’ll have what appears to be smallpox eating away your mesh.
Now, there are two things you can do. One of them is you can go back to the Map To tab and select the “Disp” button and then modify the Disp value. How does this solve the problem? It doesn’t. But it does make for some cool warped effects.
The second choice is to…and how I hate this choice…solve the problem. If you were stupid enough to select Disp and edit the Disp value before reading the entire paragraph about it, deselect it and set the value to 0. Following that, you will want to adjust only a very select few values. The key one is the NOR value (can be set from 0-25). The NOR value will adjust how far your bumps spread into space, or it will adjust your object from being smooth, to having a severe case of acne to being a mace. Adjust that for the bumps, and also, you might even want to tweak with the size of the texture. Go to the Texture tab and scale the texture several different ways. You can also go back to the texture itself and modify the noise size if you want, but the Oracle Rock wouldn’t recommend it. If you already have the texture’s preview looking good (not the material preview), then just manipulate the size and the Nor value until it is looking good enough.
I hope this helps all you out there. And remember, the only values that truly matter when tweaking that bump map are (and in no particular order):
Noise Size
Nor Val
Tex SizeX,Y,Z
ColorBand’s ColorBar Position, number and color contrast.
After the others have been set, those mentioned above are the only ones that need to be worried about. Noise Size will determine how often the bumps will occur, tex size determines their actual size (and of course how often the pattern will repeat along the object), the nor value determines their dimple size. Adjusting the color band is useful in conjunction with the noise size. Adding more bars adds more spots. You can play around with the other settings if you are curious, but I have not noticed much effect from them.
Oracle Rock says, “Happy Blending!”